Orange· Bambu Lab ABS GF
MatteHigh StrengthHeat ResistantTough / Impact ResistantChemical ResistantVapor SmoothableSandable
AMS compatible
Hard
Tricky. Wants careful tuning, strong bed adhesion, and usually an enclosure.
Sign up to follow this filament
Your spools, shelves, and drying logs, all in one visual studio.
Buy links may earn VisualSpool a small commission, at no extra cost to you.
Details.
Your spools
Sign in to see your spools of this filament here, how much is left, and where each one lives.
Bambu Lab ABS GF Orange Summary
This filament is tricky to print, heat-resistant. Worth watching: it can be prone to warping and a bit smelly to print.
Print characteristics
Layer adhesion GoodBed adhesion EasyBridging & overhang FairSpeed sensitivity HighWarping HighShrinkage 0.4-0.8 %Stringing LowOozing LowOdor Strong
Strengths
- Solid strength for everyday parts
- Handles heat well
- Prints clean with minimal stringing
- Good electrical insulator
Things to watch
- Prone to warping, use a heated bed and ideally an enclosure
- Degrades in sunlight, not ideal for long-term outdoor use
- Gives off noticeable fumes, print with ventilation or filtration
- Fussy about bed adhesion, use a brim, glue, or a textured plate
Drying
This material is fairly forgiving about moisture. When it needs drying, run it at 60-70 °C for 2-4 h. Keep it in a heated dry box while printing for the cleanest results.
Compatibility
Compatible
Required
None
Keep in a dry box
240–270 °C
80–100 °C
Color
A solid Orange filament. It reads as a light, vivid orange, close to coral.
Finish
This filament has a flat, matte finish that hides layer lines.
Finishing
SandablePaintableVapor-smoothableMachinableGlue-friendly
Common uses
⚙️ Mechanical
GearsSnap-fit enclosures
☀️ Outdoor
Automotive partsCar interior accessories
⚡ Electronics
Electronics enclosures
Specialties
MatteFlat, non-reflective surface that hides layer lines. Surface feels slightly rough or chalky.
High StrengthResists bending or pulling apart under heavy load. Very stiff.
Heat ResistantWithstands elevated temperatures (hot car, warm electronics) without deforming. Printable on standard printers. HDT ~80-120°C.
Tough / Impact ResistantEngineered to resist breaking, cracking, or shattering under impact. Unlike standard PLA, which snaps, this flexes slightly before breaking. Ideal for parts that get dropped, bumped, or stressed.
Chemical ResistantResists damage from oils, fuels, acids, industrial chemicals or solvents. For laboratory equipment, fuel system components, or chemical storage.
Vapor SmoothableReacts to chemical vapors (acetone for ABS/ASA, or other solvents) that partially melt the surface. Creates a glossy, injection-molded finish with no layer lines.
SandableEasily sanded, filed, or carved without gumming up sandpaper.
Spool Specs
1.08 g/cm³
±0.03 mm
1.75 mm
1000 g
385 m
Filament Print & Drying settings
| Nozzle temp | 240–270 °C |
|---|---|
| Bed temp | 80–100 °C |
| Print speed | < 180 mm/s |
| Flow ratio | 0.97 |
| Drying | 60-70 °C for 2-4 h |
| Moisture sensitivity | Low |
| Enclosure | Required |
More in the GF series
View all 6 colors
Photos
No community photos of Bambu Lab ABS GF Orange yet.
Upload your swatch, spool or print with this filament.
Join to add a photo
or sign inReviews for Bambu Lab ABS GF Orange filament
Be the first to review. Join for free or sign in to share your experience and prints with this filament.