Black· 3DXTech PA (Nylon) CARBONX™ NYLON 6+CF
Updated Jul 7, 2026
Carbon FiberTough / Impact ResistantWear ResistantHigh StrengthChemical ResistantHeat ResistantLow Friction
Expert
Expert. Best suited to experienced makers: enclosure, precise temps, and patience.
Sign up to follow this filament
Your spools, shelves, and drying logs, all in one visual studio.
$50.67/kg
Buy links may earn VisualSpool a small commission, at no extra cost to you.
Details.
Photos
No community photos of 3DXTech PA (Nylon) CARBONX™ NYLON 6+CF Black yet.
Upload your swatch, spool or print with this filament.
Join to add a photo
or sign inYour spools
Sign in to see your spools of this filament here, how much is left, and where each one lives.
3DXTech PA (Nylon) CARBONX™ NYLON 6+CF Black Summary
This filament is demanding to print. Worth watching: it can be prone to warping and very moisture-sensitive.
Print characteristics
Layer adhesion ExceptionalBed adhesion Requires Special PrepBridging & overhang FairSpeed sensitivity HighWarping HighShrinkage 0.8-2.0 %Stringing ModerateOozing ModerateOdor Moderate
Strengths
- Solid strength for everyday parts
- Resists oils, solvents, and chemicals
- Wear-resistant for moving and rubbing parts
- A little give without being floppy
- Layers bond strongly for clean, watertight prints
- Food-safe potential with the right setup
Things to watch
- Prone to warping, use a heated bed and ideally an enclosure
- Extremely thirsty, keep it sealed with desiccant and dry it right before printing
- Softens in heat, not for hot cars or near heat sources
- Shrinks as it cools, which can affect dimensional accuracy
- Fussy about bed adhesion, use a brim, glue, or a textured plate
Color & finish
A solid Black filament. It reads as a near-black, close to midnight blue. This filament has a textured matte surface from carbon-fiber fill.
Finishing
Machinable
Specialties
Carbon FiberContains chopped carbon fibers in a base polymer (PLA, ABS, Nylon, PETG, ASA). Creates extremely stiff, lightweight, dimensionally stable parts. Matte black finish only. Highly abrasive.
Tough / Impact ResistantEngineered to resist breaking, cracking, or shattering under impact. Unlike standard PLA, which snaps, this flexes slightly before breaking. Ideal for parts that get dropped, bumped, or stressed.
Wear ResistantResists surface wear from friction and sliding. Good for gears, bushings, conveyor parts, or any component that rubs against other surfaces.
High StrengthResists bending or pulling apart under heavy load. Very stiff.
Chemical ResistantResists damage from oils, fuels, acids, industrial chemicals or solvents. For laboratory equipment, fuel system components, or chemical storage.
Heat ResistantWithstands elevated temperatures (hot car, warm electronics) without deforming. Printable on standard printers. HDT ~80-120°C.
Low Friction Naturally slippery surface. Low coefficient of friction. For bearings and sliding parts.
Spool Specs
1.17 g/cm³
±0.03 mm
1.75 mm
750 g
267 m
Filament Print & Drying settings
| Nozzle temp | 240–270 °C |
|---|---|
| Bed temp | 80–110 °C |
| Nozzle size | 0.4 mm+ |
| Flow ratio | 1 |
| Nozzle | Hardened / abrasive-resistant nozzle required |
| Drying | 90 °C for 4 h |
| Moisture sensitivity | Very High |
| Enclosure | Required |
| Part cooling | None |
| Dry box while printing | Keep the spool in a dry box while printing |
More from 3DXTech
View all 78
Alpine Green
Apple Green
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Black
Blue
Blue Ocean
Blue Transparent
Brown
Cactus Green
Chocolate Wine
Clear
Dark Blue
Dark Blue
Dark Green
Dark Grey+53
moreReviews for 3DXTech PA (Nylon) CARBONX™ NYLON 6+CF Black filament
Be the first to review. Join for free or sign in to share your experience and prints with this filament.